Engineering steel

SACM645-JIS Nitriding Steel | 41CrAlMo7 | EN41B

SACM645 steel  is defined as Cr-M0-Al Nitriding steel as per JIS G4053 Standard.It has excellent wear resistance,high surface hardness and  fatigue strength after nitriding.This material is generally supplied in annealed condition.SACM645 is usually used for high precision machine parts,typical use are  cylinder lining, compressor parts,and hydraulic parts. 1.Chemical Composition 2.Related Specifications BS:EN41B DIN
Read More
EN9 forged carbon steel round bar

EN9 Carbon Steel |070M55 BS970 Standard

EN9 Carbon steel is a medium carbon steel with  0.5-0.6% C as per BS 970 standard.It is also known as 070M55 with tensile strength between 500-800Mpa.EN9 steel is generally supplied  in untreated condition or in the normalized condition.This material can be flame or induction hardened to produce a high surface hardness with excellent wear resistance .When hardened and tempered, it develops a tensile strength in the r
Read More
EN8 Forged carbon steel round bar

BS970 EN8 Carbon steel | 080M40

EN8 Carbon steel is a medium carbon steel with  0.36-0.44% C as per BS 970 standard. It has moderate tensile strength between 500-800Mpa.It is generally supplied in untreated condition or in the normalized condition.EN8 can be hardened by quenching and tempering on limited sections,and also can be flame or induction hardened to produce a good surface hardness(50-55HRC) with moderate wear resistance.EN8 steel can be e
Read More
C40 steel

C40|DIN 1.0511|AISI 1040|S40C

C40 carbon steel has high carbon content and can be hardened by heat treatment followed by quenching and tempering to achieve 150 to 250 ksi tensile strength.it is usually supplied as forged or normalized condition.C40 carbon steel can be welded using all welding techniques with the correct procedure,and it  has good machinability(rate at 60) after full annealing.it also can be hardened by flame or induction hardenin
Read More
C35 steel

C35|DIN 1.0501|AISI 1035|S35C

C35 steel is a medium carbon, medium tensile steel supplied as-forged or normalized condition.This steel shows excellent forgeability, reasonable strength, toughness and wear resistance. C35 is easily welded with the correct procedure.Due to the carbon content preheating and postheating are required.It has good Machinability after full annealing.Wide range of mechanical properties can be attained by quenching and tem
Read More
50CRMO4 Forged shaft

50CrMo4|DIN1.7228|AISI 4150

50CrMo4 is a higher carbon variation of the chromium, manganese, molybdenum 4100 series of low alloy steels.It has high strength,toughness,and high hardenability,and also has good machinability in annealed or normalized conditions.50CrMo4 can be welded using all conventional techniques. The mechanical properties of this steel can be affected if it is welded in the hardened condition. Post-weld heat treatment should b
Read More
34CrNiMo6 steel bar

DIN 1.6582|34CrNiMo6

DIN1.6582/34CrNiMo6 steel is a heat treatable, low alloy steel,used for a wide range of engineering parts. It is capable of being heat treated to produce a typical tensile strength of 1000 -1200 N/mm² which combined with good ductility and resistance to shock. It also has good hardenability,enabling it to be used for medium tensile strengths in fairly large sections, and attain good wear resistance,good impact proper
Read More
1.7225 forged flat bar

DIN 1.7225|42CrMo4

42CrMo4 is alloyed heat treatable steel which is used in quenched and tempered condition with a typical tensile strength of 900 -1200 N/mm².It has high strength,good wear-resistance,high fatigue strength and good low-temperature impact toughness.Similar to AISI 4140,SCM440,only a little different in Mn,Cr,this material also has good machinability,but poor in weldability. 1.42CrMo4 steel Supply Form & Size 2.Surfa
Read More
AISI 1020 forged round bar

AISI 1020|1.0402|C22|S20C

AISI 1020 steel is a low carbon steel which has at least 0.17%C and 0.3%Mn. It has a good combination of strength and ductility and can be carburized,but due to its low carbon content, it is difficult to induction hardening or flame hardening. Due to lack of alloying elements, it is not suitable for nitriding.AISI 1020 steel can be easily machined,and can be welded easily using all of the traditional methods. 1.AISI
Read More
AISI 9840 Steel bar


 AISI 9840 is a nickel-chrome-molybdenum steel  which contains at least 0.85%Ni,0.7%Cr,0.2%Mo as strengthening alloy elements.It is suitable for different heat treatment and shows excellent hardenability, strength,toughness and good cold workability.After annealing,this material  becomes machinable and adjusted for the mechanical cutting.pre-heat and post-weld stress relief are necessary for welding of this alloy,but
Read More